|
|
|
|
Product
Info • Technical
Data
Installation
Instructions
MSDS: USA: English
/ Spanish
• Canada: English / French
|
HENRY
452 General Purpose Epoxy Flooring Adhesive (Parts A &
B)
|
|
|
| Typical
Use: |
Traffic
Type: |
| A
general purpose, high-strength adhesive for installing
vinyl composition tile (VCT), felt-backed commercial sheet,
linoleum, rubber tile, most recycled rubber, rubber and
vinyl stair treads and commercial homogenous vinyl sheet
where wet operating conditions or heavy static or rolling
loads exist. |
N/A |
| Bonds: |
Bonds
To: |
| Vinyl
composition tile (VCT), felt-backed commercial sheet,
linoleum, rubber tile, rubber stair treads, vinyl stair
treads, most recycled rubber, and commercial homogenous
vinyl sheet. |
•
Suspended A.P.A. approved wood, underlayment board, cementitious
underlayment
and dry concrete that is above, on or below grade where
there is less than 3 lb./1000
sq.ft/24 hrs. as determined by the calcium chloride moisture
test (ASTM-F-1869).
• Existing resilient flooring
• Steel, Stainless Steel and Aluminum
• Ceramic tile, terrazzo, marble and polymeric poured
floors |
|
Warranty:
|
|
|
Back
to Top
|
TECHNICAL
DATA
| Base: |
Epoxy
Resin |
| Color: |
Part
A, Off White; Part B, Brown |
| Taggant
Color: |
None |
| Next
Generation: |
N |
| Open
Time: |
None |
| Working
Time: |
60
minutes. Note: Working times vary based on type of flooring,
job conditions, substrates, temperature and humidity |
| Size: |
1
gallon when mixed |
| Shipping
Unit: |
2-1
gallon containers in a case |
| Weight
Per Gallon: |
Part
A, 12.5 lbs/gal; Part B, 8.07 lbs/gal |
| Quantity
Per Pallet: |
72
cases |
| Shelf
Life: |
One
year if not opened |
| Freeze-Thaw
Stable: |
Yes |
| UPC
Information: |
Part
A: 0-42369-32312-3
Part B: 0-42369-32315-4
|
Back
to Top
INSTALLATION
INSTRUCTIONS
- DIRECTIONS:
PREPARATION
- Read
installation instructions and MSDS thoroughly prior
to installation.
- All
surfaces must be clean, dry and free of dust, grease,
paints, oils, sealers and curing compounds, or any
other foreign materials which may interfere with
proper adhesion. Condition the area to be installed,
adhesive and flooring at 65°F (18°C) or
above for 48 hours before, during and 48 hours after
installation.
- Prior
to applying adhesive to rubber stair treads, lightly
sand the entire back of the tread and nosing and
wipe with denatured alcohol to remove any contaminants
which may interfere with proper adhesion. Fill cracks
and uneven surfaces with cementitious patching compound.
NOTE: Many recycled rubber products contain chemicals
that may inhibit bond integrity. If the composition
of the recycled rubber product is unclear, conduct
a bond test.
INSTALLATION:
- Mix
452 Part A into 452 Part B. (For smaller installations,
the mix ratio is 1:1 by volume)
- Full
spread adhesive using recommended trowel.
- Before
installing floor, carefully read and follow open
time instructions for individual flooring products.
- Within
60 minutes, cut, fit and reposition as recommended.
- Roll
floor in both directions with a 75-100 lb. roller
or flooring manufacturer’s recommended roller
across width and length and seal seams on sheet
flooring as recommended by the flooring manufacturer.
|
Application
|
Recommended
Trowel
|
Coverage
|
|
All
|
|
225-275 sq. ft.
(25-31 sq yds/gal) |
Click on the icons above to
calculate the amount of product you need!
CLEANUP:
- Wet
Adhesive: Clean, white cloth dampened with soapy
water.
- Dried
Adhesive: Can not be removed.
WARNINGS:
Carefully read and follow all cautions and warnings
on the product label. Refer to the Material
Safety Data Sheet for additional product information.
|
|
|
