|
|
|
|
Product
Info • Technical
Data
Installation Instructions
MSDS:
USA: English
/ Spanish
• Canada: English
/ French
|
HENRY
422 Premium Vinyl-Backed Flooring Adhesive
-
Long
Working Time
-
Builds
Strength Fast
-
Very
Strong Ultimate Bond
-
Outstanding
Plasticizer Migration Resistance
-
Non-Staining
-
Moisture
and Alkali Resistance
- Excellent
Dimensional Stability
|
|
|
| Typical
Use: |
Traffic
Type: |
For
easy, fast and permanent installations of
solid vinyl tile and vinyl plank, luxury vinyl tile, vinyl stair treads,
vinyl-backed carpet and carpet tile and vinyl-backed resilient sheet flooring. |
N/A |
| Bonds: |
Bonds
To: |
| Permanent
installations of solid vinyl tile and vinyl plank,
luxury vinyl tile, vinyl stair treads, vinyl-backed
carpet and carpet tile and vinyl-backed resilient sheet
flooring. Mannington HP backed carpet. |
POROUS
Suspended A.P.A. approved wood, underlayment board, cementitious underlayment,
and dry concrete that is above, on or below grade where there is less
than 3 lb./1000 sq. ft./24 hrs. as determined by the calcium chloride
moisture test (ASTM-F-1869).
NON-POROUS
Staircases, terrazzo, ceramic tile, metal, existing fully adhered solid vinyl
resilient on all grade levels and poured polymeric floors.
NOTE: Not recommended for installation over
soft resilient floor coverings. |
|
Warranty:
|
|
|
Back
to Top
|
TECHNICAL
DATA
| Base: |
Filled
Latex |
| Color: |
Off
White |
| Taggant
Color: |
Yellow/Orange |
| Next
Generation: |
No |
| Open
Time: |
Porous:
15-25 minutes. Non-Porous: 30-40 minutes. |
| Working
Time: |
Porous:
60-90 minutes. Non-Porous: up to 2 hours. Note: Working
times vary based on job conditions, substrates, temperature
and humidity. |
| Size: |
4
Gallon |
1
Gallon |
| Shipping
Unit: |
1
pail |
1
case |
| Weight
Per Gallon: |
11.20
lbs |
11.20
lbs |
| Quantity
Per Pallet: |
48
pails |
30
cases |
| Shelf
Life: |
One
year if not opened |
| Freeze-Thaw
Stable: |
Protect
From Freezing. Store adhesive in room between 40°F
and 90°F. |
| UPC
Information: |
4
Gallon: 0-42369-32313-0 |
1
Gallon: 0-42369-323147 |
Back
to Top
INSTALLATION
INSTRUCTIONS
|
DIRECTIONS:
PREPARATION
PREPARATION
• Read installation instructions and MSDS thoroughly prior to installation.
• All surfaces must be sound, smooth, dry, clean, free of excess moisture
and alkali. Remove dirt, wax, loose paint and all foreign matter that would interfere
with a good bond, such as curing agents and sealers. Condition the area to be
installed, adhesive and flooring at 65°F (18°C) or above for 48 hours
before, during and 48 hours after installation.
• Refer to the flooring manufacturer’s specific recommendations for
subfloor preparations.
• Always run a calcium chloride and alkali test over concrete on any grade
level. For accurate results, curing agents must be removed in areas where tests
will be run. Moisture test results should meet the flooring manufacturer’s
recommendations, but should not exceed 3 lbs./1000 sq.ft/24 hrs., as determined
by the calcium chloride moisture test (ASTM-F -1869).
Alkali readings should be 5 to 9.
INSTALLATION:
• Stir any liquid on the surface into the adhesive and full spread adhesive
using recommended trowel.
POROUS SUBSTRATES
• Spread adhesive evenly on the substrate
with a 1/16” x 1/16” x 1/16” Square-notched
trowel. Allow adhesive to remain open about 15-25
minutes. Working time over concrete, up to 90
minutes depending on temperature and humidity
during installation. Roll flooring material with
a 75-100 lb. roller or flooring manufacturer's
recommended roller across width and length.
NON-POROUS SUBSTRATES
• Spread adhesive evenly on substrate using a1/32"D x 1/16"W x
5/64"A U-notch trowel.Allow adhesive to dry for approximately 30-40minutes,
depending on temperature and humidityconditions. Working time up to 2 hours,depending
on temperature and humidityconditions. Roll flooring material with a 75-100lb.
roller or flooring manufacturer's recommended roller across width and length.
NOTE: Avoid traffic for 12 hours after installation.
|
Application
|
Recommended
Trowel
|
Coverage
|
| Porous |
|
125 sq ft/gal
|
| Non-Porous |
|
160 sq ft/gal |
Click on the icons above to
calculate the amount of product you need!
CLEANUP:
- Wet
Adhesive: Clean, white cloth dampened with soapy
water.
- Dried
Adhesive: Clean, white cloth dampened with mineral
spirits; carefully following warnings on the container.
WARNINGS:
Carefully read and follow all cautions and warnings
on the product label. Refer to the Material
Safety Data Sheet for additional product information.
|
|
|
