|
|
|
|
Product
Info • Technical
Data
Installation
Instructions
MSDS:
USA: English
/ Spanish
• Canada: English
/ French
|
HENRY
263 WeatherPro Outdoor Carpet Adhesive
-
Waterproof
-
Excellent
Initial Grab
-
No
Open Time Required
-
Ample
Working Time
-
Excellent
-
Excellent
Trowelability
|
|
|
|
| Typical
Use: |
Traffic
Type: |
| Installation
of carpet outdoors. HENRY 263 WeatherPro is waterproof
within two hours after installation and can be used in
wide temperature ranges. |
Outdoors
only |
| Bonds: |
Bonds
To: |
Outdoor
carpet and artificial turf
OUTDOOR USE ONLY
DO NOT USE INDOORS. |
Concrete,
asphalt paving, abraded fiberglass substrates, roughened
aluminum boat decks and exterior or marine grade plywood
decking as recommended by the carpet manufacturer. We
cannot be responsible for failures resulting from deterioration
of the plywood itself. Substrates that have been painted,
stained or otherwise coated must be tested to assure compatibility
with the adhesive. |
| Warranty: |
| HENRY's Best 10 Year Warranty |
Back
to Top
|
TECHNICAL
DATA
| Base: |
Solvent-based/rubber-resin |
| Color: |
Tan |
| Taggant
Color: |
Yellow/Orange |
| Open
Time: |
None |
| Working
Time: |
30
minutes NOTE: Working times vary based on job conditions,
substrates, temperature, and humidity. |
| Size: |
Quart,
Gallon, 3.5 Gallon, 5 Gallon |
| Shipping
Unit: |
Quart:
12 quarts/ctn
Gallon: 4 gallons/ctn
3.5 Gallon: 1 pail
5 Gallon: 1 pail |
| Weight
Per Gallon: |
9.3
lbs |
| Quantity
Per Pallet: |
Quart: 52 ctns
Gallon: 45 ctns
3.5 Gallon: 48 pails
5 Gallon: 36 pails |
| Shelf
Life: |
One
year if not opened |
| Freeze-Thaw
Stable: |
Not
affected |
| UPC
Information: |
Quart: 0-81833-26330-5
Gallon: 0-81833-26340-4
3.5 Gallon: 0-81833-26360-2
5 Gallon: 0-81833-26370-1 |
Back
to Top
INSTALLATION
INSTRUCTIONS
|
DIRECTIONS:
Refer to carpet manufacturer’s
specific recommendations. Condition the area to be installed,
adhesive and flooring at 45°F (7°C) or above
for 48 hours before, during and 48 hours after installation.
Floor must be sound, smooth, dry, clean and free of
excessive moisture or alkali. Remove dirt, wax, loose
paint and all other foreign matter that would interfere
with a good bond such as curing agents and sealers.
- Stir
any liquid on the surface into the adhesive.
- Full
spread adhesive using recommended trowel NOTE: Recommended
trowel sizes are guidelines only, and are minimum
requirements. Rough, porous concrete and heavily textured
carpet backings may require deeper notches. A 100%
transfer of adhesive into the carpet backing, while
maintaining full coverage of the substrate, must be
obtained.
- Install
carpet immediately into wet adhesive. Do not let adhesive
skin over.
- Within
30 minutes, cut, fit and reposition as recommended
by the carpet manufacturer. Lift a newly laid area
occasionally to make sure adhesive is transferring
to back.
- Smooth
the bonded area with firm pressure using a 2-foot
length of carpet tube. It is essential to use a light
roller for polypropylene-backed carpets. Avoid squeezing
adhesive up at the seams. Seams in rubber-backed goods
may peak slightly after fitting, and small bubbles
may appear in the field. These come from temporary
swelling of the rubber back and will stay down when
adhesive starts to set.
- Seal
seams as recommended by the carpet manufacturer.
|
Application
|
Recommended
Trowel
|
Coverage
|
| All
recommended outdoor carpet backings |
|
90-108 sq. ft.
(10-12 sq yds/gal)
|
Click
on the icons above to calculate the amount of product
you need!
CLEANUP:
- Wet
Adhesive: Clean, white
cloth dampened with soapy water.
- Dried
Adhesive: Clean, white
cloth dampened with mineral spirits; carefully following
warnings on the container.
WARNINGS:
Carefully read and follow all cautions and warnings
on the product label. Refer to the Material
Safety Data Sheet for additional product information.
|
Back
to Top
|
|
